How to Replace Front Brake Pads and Rotors 2015–2022 Chevy Colorado/GMC Canyon Detailed DIY Guide!
Remember to like and subscribe for more videos, and to help me continue making them!
Amazon links to parts/tools I use, or similar, can be found below! (As available)
Products/Parts:
CRC Brakleen: https://amzn.to/49voqLA
PowerStop Coated Rotor: https://amzn.to/4o4GORm
PowerStop Ceramic Brake Pads: https://amzn.to/4wYBWBv
Permatex Thread Locker Red: https://amzn.to/4o2YQU8
VersaChem Brake Caliper Grease: https://amzn.to/3PyzXTC
*Verify part fitment for your specific vehicle.
Tools:
Craftsman 3/8" Drive Long Handle Ratchet: https://amzn.to/3RzkdjR
Craftsman 3/8" Metric Socket Set: https://amzn.to/3PEIZyq
Craftsman Torx Bit Socket Set: https://amzn.to/4uRRTbe
Craftsman Long Nose Pliers: https://amzn.to/4wTsVcG
Craftsman 16ox Fiberglass Hammer: https://amzn.to/4dSg6Ip
Deep C Clamp: https://amzn.to/4o7WoMe
Lexivon 3/8" Drive Torque Wrench: https://amzn.to/435f6ua
Punch Set: https://amzn.to/4dHuXVU
As an Amazon Associate I earn commissions from any qualifying purchases!
0:00 - Intro and Tools/Parts Used
2:34 - Loosen Brake Hardware for Removal
4:45 - Remove and Support Caliper
5:55 - Compress Caliper Pistons
7:48 - Remove Rotor Mounting Bolt
8:30 - Brief Note on Drilling Out Rotor Mounting Bolt
10:17 - Remove Rotor
11:45 - Remove Brake Pins and Hardware
14:19 - Remove Brake Pads
14:55 - Clean and Prep for Reinstallation
15:29 - Brief Note on Removing Brake Line
16:08 - Compare Old and New Parts
17:03 - Install New Pads and Hardware
20:33 - Install New Rotor
21:33 - Reinstall Caliper and Pads Assembly
23:25 - Final Inspections/Completion
In this video I show how I removed and replaced front brake pads and rotors on my 2018 Chevy Colorado Z71 4WD with the 3.6L. This is a detailed video on the steps I took and how I resolved any issues I ran into. I also briefly go over how I removed the rotor screw using a drill and screw extractor when the head stripped out.
I assume this method would be the same for all 2nd gen (2015-2022) Colorados, GMC Canyons, and even many rear-wheel-drive vehicles, assuming differing clearances and socket sizes. Verify application for your vehicle.
Hopefully you find this video helpful! Feel free to discuss what has or hasn't worked for you in the past.
Disclaimer: I am not a professional mechanic, nor do I claim to be. This video is for entertainment purposes only and shows how I accomplished the work. The methods and processes I used are not necessarily as outlined or recommended by GM. Always refer to GM/Chevrolet/GMC or your vehicle's manuals as explained and outlined by GM. I have not been endorsed by any of the companies or brands mentioned in this video. All opinions are entirely my own. I assume no liability for any damage or injury incurred by information in this video. Information to be used at your own risk. Due to factors beyond my control, no information in this video shall create any expressed or implied guarantee of any particular result. Injury, damage, or loss from improper use of tools, equipment, or information in this video is the viewer's responsibility.