WTFOS & V01.07.0000 COMPATIBILITY Issue Fix | DJI Goggles V2 Gets Native Betaflight 4.4 HD OSD
The DJI Goggles V2 also supports the Betaflight 4.4 native HD OSD when paired with the O3 air unit. However, if you have WTFOS installed, there is a compatibility issue that causes the Canvas Mode menu option to disappear from the Display menu on the goggles. These instructions will resolve that. Thanks to K1200S08 for sharing these instructions with me!
=========================
Items suggested in this video
=========================
My Favorite Screwdrivers (Wiha Slotted & Phillips):
Amazon US: https://amzn.to/3tq15Eu
Amazon Canada: https://amzn.to/3E1Ph02
DJI Goggles 2 Integra:
Amazon US: https://amzn.to/40DmrND
Amazon Canada: https://amzn.to/3Kdzd0y
GetFPV: http://bit.ly/40IFvux
DJI FPV Goggle V2:
Amazon US: https://amzn.to/3H9FGZk
Amazon Canada: https://amzn.to/3VLHQlY
DJI O3 Air Unit:
Amazon US: https://amzn.to/3WZnupK
Amazon Canada: https://amzn.to/3jJszUR
GetFPV: https://bit.ly/3ioEE1s
DJI FPV Remote Controller 2:
Amazon US: https://amzn.to/3EPa8oJ
Amazon Canada: https://amzn.to/3XJRZ4w
XING2 1404 4600kv Motors:
Banggood: https://www.banggood.com/custlink/mG3...
GetFPV: http://bit.ly/3GQa7mz
iFlight 20x20mm F7 Flight Stack:
Banggood: https://www.banggood.com/custlink/3vK...
GetFPV: http://bit.ly/3vLrWx3
HQ T3x3x3 Props
Banggood: https://www.banggood.com/custlink/G3v...
GetFPV: http://bit.ly/3Zo04fR
TBS Crossfire Nano Receiver with Immortal T Antenna
GetFPV: http://bit.ly/3Zm2WK6
TBS Tango 2 Pro
GetFPV: https://bit.ly/3QsPlgj
SpeedyBee F7 Mini 35A 3-6S 8-bit Flight Controller Stack:
GetFPV: http://bit.ly/3kIHP50
XING2 1404 4600kv Motors:
Banggood: https://www.banggood.com/custlink/mG3...
GetFPV: http://bit.ly/3GQa7mz
Happymodel EP1 ELRS Receiver:
AliExpress: https://s.click.aliexpress.com/e/_DEH...
GetFPV: http://bit.ly/3GRtYC8
HQ T3x3x3 Props
Banggood: https://www.banggood.com/custlink/G3v...
GetFPV: http://bit.ly/3Zo04fR
=========================
Instructions & CLI Commands
=========================
Here are the steps you should follow to get both O3 OSD HD and WTFOS work (MUST do in the exact order):
Boot the goggles into FPV System (DIY) mode and connect to FPVWTF configurator
Remove WTFOS and reboot into O3 mode
Connect to DJI Assistant (Consumer Drone series) and update firmware to 1.07.0000
After update completed, swith back to FPV System (DIY) mode, reboot and connect to fpv.wtf configurator
Run the CLI commands:
unrd slot_1.status_successful 0
unrd slot_1.status_active 0
unrd slot_2.status_active 1
reboot
After the goggles rebooted, the configurator detected the slot problem and offered an automatic fix. Accept the fix.
After automated fix applied, re-install WTFOS
Reinstall packages (msp-osd, etc)
============================
Videos you may want to check out
============================
How to get your custom BetaFlight OSD working on the DJI O3 Air Unit | MSP Canvas Mode is HERE!
• How to get your custom BetaFlight OSD work...
You FINALLY Did It! | DJI Goggles 2 Native Betaflight 4.4 HD OSD Now Officially Supported
• You FINALLY Did It! | DJI Goggles 2 Native...
FULLY Customizable HD OSD canvas mode for DJI FPV Goggles V1 & V2 | My EYES can't handle the BEAUTY!
• FULLY Customizable HD OSD canvas mode for ...
Playlist: DJI O3 Digital FPV System | Reviews, Guides, & How Tos
• DJI O3 Digital FPV System | Reviews, Guide...
#djifpv #fpv #drones
Mandatory Disclaimer: I participant in the Amazon Services LLC Associates Program, which is an affiliate advertising program designed to provide a means to earn fees by linking to Amazon.com and affiliated sites. Item suggestion links above are affiliate links and I will receive compensation if you choose to use them. There is no cost to you to use these links and any compensation received goes right back into the channel.