Rebuilding a 3.4L TRD 5VZ-FE V6 Supercharger (PTR01-35962) - Eaton Rear Needle Bearing Replacement
Did our video help you? If so, consider buying us a beer!: https://bit.ly/3feE6tJ
In this video, we show you how to replace the rear needle bearings in the back of a 3.4l 5VZ-FE TRD Supercharger System (PTR01-35962). We had a unique opportunity to showcase two different housings of the black 2nd Gen Supercharger which forces you to use a blind bearing puller on one of the rear needle bearings. If you have a 1st Gen gray style Supercharger, this video will still help you understand what is needed to replace your rear needle bearings.
TRD Supercharger Installation • Toyota 5VZ-FE 3.4L V6 TRD Supercharger Ins...
TRD Supercharger Nose Cone Rebuild • Toyota 5VZ-FE 3.4L V6 TRD Supercharger Nos...
*COMPLETE REBUILD KITS:*
Eaton https://ebay.us/T5aMc3
Genuine Toyota https://ebay.us/4sLy86
Here are some helpful resources to help with any related installation of a Supercharger:
T4R.ORG 3.4L Supercharger Thread http://www.toyota-4runner.org/3rd-gen...
TRD Installation Instructions https://drive.google.com/open?id=19DR...
Magnuson Installation Instructions http://www.lcengineering.com/LCInstru...
_______HELPFUL TOOLS_______
If you're looking for other tools not used in this video, check out Timmy's Master Tool List.
https://www.amazon.com/shop/timmythet...
*4 Piece 3 Jaw Puller Set - (the 3 jaw puller you might need to use to get the pulley off the nose cone shaft)
https://amzn.to/2sIUWIF
*Harbor Freight 20 Ton Press
https://www.harborfreight.com/automot...
*Press Sleeve Kit - (used this for the press work. We have used this kit lots of times)
https://amzn.to/34JjiAs
*1/4" and 3/8" Flex Head Ratchet Set
https://amzn.to/2ql8nNA
*1/4” Drive Regular Extension Set
https://amzn.to/2O9nl2x
*1/4” Drive 6 Point Standard Metric Socket Set
https://amzn.to/2QIU7te
*90 Degree Needle Nose Pliers
https://amzn.to/2VYUro8
*SAE Allen Head Socket Set - (used a 3/16" allen socket for drain/fill plug)
https://amzn.to/346IVt8
*3/8" Drive 6 Point Metric Standard Socket Set
https://amzn.to/32WIh0M
*3/8" Drive 6 Point Metric Deep Socket Set
https://amzn.to/37iQjVt
*Long Set of Ratcheting Box End Wrenches - (used 10mm for lower nose cone bolt)
https://amzn.to/2oOhndL
*Milwaukee Mi12 Cordless Ratchet
https://amzn.to/2utRZsE
*Milwaukee M12 Battery
https://amzn.to/3FJZO1j
*Milwaukee M12 High Capacity Battery
https://amzn.to/2HEFTpu
*Milwaukee M12 Battery Charger
https://amzn.to/2uo2o9x
*Impact Socket Adapter and Reducer Set - (used a 3/8" to 1/4" reducer)
https://amzn.to/34DwxlA
*Mayhew 5 Piece Prybar Set - (used a smaller length pry bar to separate nose cone from main supercharger housing. This is a nice complete set) https://amzn.to/2Ob8THw
*Strap Wrench Set - (used the smaller of the two in this kit to hold pulley firm when loosening and tightening the pulley nut)
https://amzn.to/2FdjT1D
*20 Piece Screwdriver Set - (used a flat blade screwdriver to get the coupler off. This is a nice set if you're in the market for one.)
https://amzn.to/34aLrQ1
*1/2" Drive Deep Metric Impact Socket Set - (used a 22mm from this set)
https://amzn.to/2WfSTGD
*1/2" Drive Shallow Impact Socket Set - (used a 17mm from this set)
https://amzn.to/2pCrdPQ
*1/2" Drive Regular Impact Extension Set - (used an extension with the 22mm socket to drive out the outer bearing and seal)
https://amzn.to/2J7FYko
*22mm Extra Deep Impact Socket - (To drive the shaft back into the nose cone housing. You need an extra long socket so you don't end up damaging the threads on the nose cone spindle.)
https://amzn.to/2FrhuAJ
*Plastic Mallet - (To pound coupler into place)
https://amzn.to/2CCOqVP
*Internal Retaining Ring Pliers - (To install seal retaining clip)
https://amzn.to/2SKZUPJ
*Yost Bench Vice - (Vice I own. Yost makes very nice bench vices)
https://amzn.to/2ofa4LD
*Yost 6” Soft Vice Jaw Caps - (soft jaws used with the Yost bench vice)
https://amzn.to/2YPAQbo
*242 Loctite
https://amzn.to/2puKrHn
*CDI 3/8" Drive 10-100 Foot Pound Torque Wrench - (To torque nose cone bolts)
https://amzn.to/2U2vUA4
*10cc Syringe - (used with 7/64" window washing hose to draw oil out of nose cone)
https://amzn.to/2Wd8S8l
*7/64” Window Washing Hose - (used a 6" section with the 10cc syringe to draw oil out)
https://amzn.to/3wRWME9
**As Ebay Partner Network members, we earn commissions from qualifying purchases.
**As Amazon Associates, we earn from qualifying purchases.