Complete Traxtech Track Mount Installation Guide | Install Boat Tracks the RIGHT Way!
Complete Traxtech Track Mount Installation Guide | Step-by-Step DIY Boat Track Installation
Ready to upgrade your fishing boat with a Traxtech track system? In this complete step-by-step Traxtech track mount installation guide, I'll show you exactly how to install Traxtech tracks the right way—from planning the layout and measuring your mounting locations to drilling, countersinking, sealing, and securing the tracks for a clean, professional, and watertight installation.
Whether you own an aluminum fishing boat, deep V boat, Lund, Crestliner, Princecraft, Alumacraft, Smoker Craft, Starcraft, or any other fishing boat, these installation techniques will help you build a strong and reliable track system that will last for years.
A properly installed Traxtech track system gives you the flexibility to mount rod holders, planer board reels, downriggers, electronics, LiveScope poles, tool holders, net holders, cup holders, camera mounts, and many other fishing accessories without drilling unnecessary holes in your boat every time you add new equipment.
Step 1 – Plan Your Layout
Before drilling a single hole, take time to determine exactly where you want your Traxtech tracks. Think about how you'll be fishing throughout the season. Consider where your rod holders, downriggers, planer board reels, electronics, and accessories will be mounted and make sure there is enough room for them to operate without interfering with passengers or other equipment.
Check underneath the mounting surface for wiring, fuel lines, flotation foam, supports, or anything that could be damaged during drilling.
Step 2 – Measure Everything Twice
Accurate measurements are one of the most important parts of the installation.
Measure the distance from the gunwale and reference points on your boat to ensure both tracks are perfectly straight and evenly spaced. Use a tape measure, straight edge, or level to verify alignment before marking any holes.
Taking a few extra minutes here will give your boat a clean, factory-installed appearance.
Step 3 – Tape the Installation Area
Apply painter's tape where the tracks will be installed.
The tape helps protect your boat's finish while allowing you to clearly mark every mounting hole. It also helps reduce paint chipping around the holes when drilling.
Place the Traxtech track on the tape, double-check your measurements, and carefully mark every hole before removing the track.
Step 4 – Drill Pilot Holes
Start with a small pilot drill bit before using the final drill size recommended by Traxtech.
Drilling pilot holes helps keep the larger drill bit centered and reduces the chance of the bit walking across the aluminum surface.
Drill slowly using steady pressure and remove any aluminum shavings before moving to the next hole.
Step 5 – Chamfer (Countersink) Every Hole
One of the most overlooked installation steps is using a chamfer or countersink bit.
Lightly chamfering each hole removes sharp edges and helps prevent cracks from forming around the mounting holes over time. It also creates a cleaner finish and allows the marine sealant to bond more effectively.
This simple step can greatly improve the long-term durability of your installation.
Step 6 – Apply Marine Sealant
Before installing the hardware, apply a generous amount of high-quality marine sealant around every hole.
Marine sealant helps prevent water intrusion, corrosion, and long-term damage inside your boat. Every fastener should be sealed to protect the aluminum and keep your boat watertight.
Wipe away any excess sealant once the hardware has been tightened.
Step 7 – Install the Hardware
Place the Traxtech track back into position and install all mounting bolts by hand before tightening them.
Gradually tighten each fastener in an alternating pattern so the track seats evenly against the boat.
Avoid overtightening, which can damage the aluminum or squeeze out too much sealant.
Once installed, inspect every bolt and verify the track is straight, secure, and ready for use.
Why Install a Traxtech Track System?
A Traxtech track system is one of the best upgrades you can make to a fishing boat because it allows you to quickly reposition accessories without drilling additional holes. Whether you're trolling for salmon on the Great Lakes, targeting giant muskies, chasing northern pike, jigging for walleye, or bass fishing, a modular track system makes your boat more organized, more versatile, and easier to customize for every trip.
If this guide helped you install your Traxtech tracks, don't forget to:
👍 Like the video
💬 Comment with your questions or your own installation tips
🔔 Subscribe for more fishing content, boat upgrades, DIY projects, and on-the-water adventures every week.
Tragedy by Alex-Productions / alexproduction. .
Creative Commons — Attribution 3.0 Unported — CC BY 3.0
Free Download / Stream: https://bit.ly/3vZbLx6
Music promoted by Audio Library • Tragedy – Alex-Productions (No Copyright M...