Volvo XC60 D3 Oil Change Guide (2008-2016) - Step-by-Step DIY
Volvo XC60 Oil & Filter Change - Step-by-Step DIY Guide (2008-2016 D3 & Similar 5-Cylinder Engines)
⚠️ PLEASE NOTE: The oil used in this video is not the correct oil. I have used 0w 20 which is ok but the recommended oil is 0w 30. Please make sure you cross check your specific vehicle to find the correct grade of oil.
Learn how to perform a complete engine oil and filter change on your 2011 Volvo XC60 D3 (Engine Code: D5204T3) with this comprehensive, step-by-step video guide. This procedure is also similar for most Volvo 5-cylinder engined cars, particularly models manufactured between 2008 and 2016.
Save money and gain confidence by tackling this essential maintenance task yourself! We cover everything from safely raising your vehicle to refilling with new oil, including crucial torque specifications.
🔑 What you'll learn in this video:
Safely raising your Volvo XC60.
Removing the undertray for access.
Draining old engine oil.
Replacing the oil filter and O-ring.
Properly refitting the sump drain plug and oil filter housing.
Filling the engine with new oil and checking levels.
Important checks for leaks.
🛠 Tools & Parts You'll Need (with affiliate links for convenience):
Service Kit (specific to 2011 XC60 D3): https://ebay.us/3tbc1K
General Service Kit Search: https://ebay.us/xVKW5Y
Replacement Service Booklet: https://ebay.us/2B6Aqd
T30 Torx or 12mm socket (for undertray)
36mm socket (for oil filter housing)
17mm socket (for sump drain plug)
Torque wrench
Container for old oil
New oil filter
5.9 litres of specified engine oil (e.g., SAE 0W-20 Fully Synthetic – Mannol Legend Ultra, always check your vehicle's recommendation!)
New oil drain plug washer
Means to safely raise the vehicle (ramps, jack, axle stands)
(As Amazon Associates and eBay Partners, we earn from qualifying purchases at no extra cost to you.)
⏰ Chapters:
0:00 - Introduction
1:05 - Removing the undertray
1:40 - Draining the engine oil
2:25 - Removing & renewing the oil filter
4:45 - Refitting the oil filter housing
5:10 - Fitting the new sump drain plug
5:55 - Filling the engine with new oil
6:30 - Starting the engine, checking for leaks & level
Detailed Procedure Steps:
Run the engine to normal operating temperature.
Safely raise the front of the car.
Remove the engine undertray (T30 Torx drive).
Position a suitable container under the oil drain plug.
Remove the oil drain plug (17mm socket) and drain the hot oil.
While draining, remove the oil filter housing (36mm socket).
Replace the old filter, clean the housing, and install a new O-ring (lubricate with oil). Fit the new filter and reinstall the housing (torque to 25Nm).
Reinstall the drain plug with a new sealing washer (torque to 35 Nm).
Fill the engine with the correct new oil (refer to your vehicle's manual for type and quantity). Check the level using the dipstick or electronic display.
Start the engine, check for leaks around the filter and drain plug. Re-check oil level on level ground and top up if necessary (do not overfill).
Reinstall the undertray.
🔗 Making the Ramps Used in This Video: [Insert Link Here]
If you found this video helpful, please give it a Thumbs Up 👍 and consider subscribing to Everyday Workshop Channel for more DIY car maintenance and workshop content! Your support really helps.
Support the Channel:
If you'd like to support my work and help me create more content, you can buy me a ☕️ or 🍺 here: https://www.buymeacoffee.com/Everyday... Thank you!
#Volvo #XC60 #OilChange #DIYCarMaintenance #D3Engine #VolvoRepair #EverydayWorkshop #CarMaintenance #StepByStep #AutomotiveDIY