End Grain Piano Cutting Board
MEASUREMENTS FOR THIS BOARD ARE BELOW.
This video takes you in the step by step process on how to make a end grain piano cutting board.
Mandocello & Octave Mandolin blueprints: https://www.hovingtoninstruments.com/...
TOOLS & CONSUMABLES
Starbond Affiliated link: https://www.starbond.com/?rfsn=455717...
Use TOMY10 at checkout
Needle Files https://amzn.to/39ehKTl
Nut files https://amzn.to/3qGpx22
End fret file https://amzn.to/366IjYE
Spool clamps https://amzn.to/3oerpNK
Luthier's Clamps https://amzn.to/39ehdRl
Stanley coping saw https://amzn.to/2KQaljG
Jeweler saw & blades https://amzn.to/3ocF7R9
Card Scraper set https://amzn.to/3t3rdom
Protractor https://amzn.to/3o9rn9W
Dial indicator https://amzn.to/3pjuDRt
String winder https://amzn.to/3sThUXR
Binding glue (Duco) https://amzn.to/39YP0gu
Table saw blade: https://amzn.to/3iKeGkF
Dado Oshlun 6" https://amzn.to/3cch9Dl
Wood Slicer Bandsaw blade by Highland Woodworking
Dewalt router kit https://amzn.to/3iPAEmv
Dewalt variable speed sander https://amzn.to/39iZGHL
Porter cable drill and impact combo https://amzn.to/3sSCdon
Dremel https://amzn.to/3sSxF18
Dremel base https://amzn.to/3sUBEKz
Inlay bits: https://amzn.to/3psw8Nv
My Video gear
Camera: Iphone 11 pro: https://amzn.to/3peiEEU
Canon T5i: https://amzn.to/3sStItk
Yongnuo 35mm: https://amzn.to/39fFqXg
Yongnuo 50mm: https://amzn.to/3a3Ynvl
SD card: https://amzn.to/2LUbd7s
External harddrive LaCie 5T: https://amzn.to/3ofhN5l
How to maintain your end grain cutting board: • How to Maintain Your End Grain Cutting Board
www.lumberjocks.com
http://lumberjocks.com/projects/103083 Suit and tie cutting board
http://lumberjocks.com/projects/98256 key board
My Lumberjocks at: http://lumberjocks.com/Gbluee/projects
Measurement for the board:
The final dimentions for my Board is 16 1/2 x 10 1/2. The white keys are made with maple and have a width of 7/8 "inches. The bands are 1/16" thick walnut . You must make a 3pieces set of maple, and a 4 piece set.
The black keys are 9/16 " thick, and the maple between the black key is 5/8"(*look at note at the bottom*). When your maple assembly is made you can determine the required thickness for the maple located outside of the black keys .
The thickness of the board is cut 2 ", so I cut my pieces to 2 1/8 to be able to obtain the desired thickness after planning.
(**) There was a little mistake that i've made while in the process of building the board. when building the sharp and flat keys (black keys) the block with the F# to Bb (3 black keys) needs a different spacing then the other block. If you look carefully to the pictures of my board, the lines from the keys below end up being in line with the side of the keys. I've notice too late and decided not to waste the wood and carried on with the project. all that needs to change is the thinkness of the maple strips between the F# and G# and between, the G# and Bb to get the walnut lines from the white keys to line up more properly. And also adjust the outside maple thickness of the block accordingly..
More Music by Jazzar at: http://www.betterwithmusic.com/
More Music by Kevin MacLeod at:http://incompetech.com/