How to use KK2.1.5 Multirotor LCD Flight Control Board, Explain in hindi
How to use KK2.1.5 Multirotor LCD Flight Control Board, Explain in hindi
For more details visit our website https://trybotics.com
For more quadcopter related project, visit https://trybotics.com/project?search=...
If You want to buy this Quadcopter parts then visit our website https://trybotics.com/buy
Or you can click the below link to buy quadcopter parts
Complete DIY Quadcopter Kit In Lowest Price:
https://trybotics.com/buy/37
Complete DIY Quadcopter Kit In Lowest Price (Without RC Remote Controller)
https://trybotics.com/buy/38
Quadcopter Kit In Lowest Price:
https://trybotics.com/buy/3
Quadcopter Motor, Esc, Propeller 4 pieces set (In lowest price):
https://trybotics.com/buy/4
Quadcopter Motor 4 pieces set (In lowest price):
https://trybotics.com/buy/5
Quadcopter Esc 4 pieces set (In lowest price):
https://trybotics.com/buy/6
Quadcopter Propeller 4 pieces set (In lowest price):
https://trybotics.com/buy/2
Quadcopter Motor, Esc, Propeller single piece set (In lowest price):
https://trybotics.com/buy/8
Quadcopter Motor single piece set (In lowest price):
https://trybotics.com/buy/9
Quadcopter Esc single piece set (In lowest price):
https://trybotics.com/buy/10
Quadcopter Flight Controller KK 2.1.5 board (In lowest price):
https://trybotics.com/buy/11
Quadcopter Flight Controller Thunder QQ Super board (In lowest price):
https://trybotics.com/buy/12
Quadcopter RC Remote (In lowest price):
https://trybotics.com/buy/13
Quadcopter Lipo battery (In lowest price):
https://trybotics.com/buy/14
Quadcopter Lipo battery Charger (In lowest price):
https://trybotics.com/buy/15
Quadcopter Frame (In lowest price):
https://trybotics.com/buy/39
Quadcopter Lipo Battery Alarm (In lowest price):
https://trybotics.com/buy/1
The KK2.1 is next big evolution of the first generation KK flight control boards. The KK2.1 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts!
The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2.1 is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory.
If you’re new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.1 was built for you. The board comes preprogrammed from Robokits and no PC or special software is required at all to get your multi-rotor flying. Everything from PID and RC tuning can be done by inbuilt gui with LCD and buttons.
Specifications:
Size: 50.5mm x 50.5mm x 12mm
MCU : Atmega644 PA
Gyro/Acc: MPU6050
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels).
Signal to ESC: 1520us.
Pre-installed firmware :
Dualcopter
Tricopter
Y6
Quadcopter +
Hexcopter +
Hexcopter +
Hexcopter X
Octocopter +
Octocopter X
X8 +
X8 X
H8
H6
V8
V6
Aero 1S Aileron
Aero 2S Aileron
Flying Wing
Singlecopter 2M 2S
Singlecopter 1M 4S
(Custom Mix via the "Mixer Editor" option):
The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.
The KK2.1 Multi-Rotor controller is a flight control board for multi-rotor aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the 6050MPU gyro/acc (roll, pitch and yaw) then passes the signal to the Atmega644PA IC. The Atmega644PA IC unit then processes these signals according the users selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft..