Carrier Ac Error Codes List | Carrier Air Conditioner All Error Codes And Solution
This video is to help assist with All Error Codes for carrier ke sabhi Error code Aapko mill jayge, Error code indoor or outdoor se pata karte hai, jaise konsi light kitni baar blink ho rahi hai..
ERROR CODE KI PURI LIST K LIAY APNA MAIL ID COMMENTS ME BTAY THANK YOU..
LIKE | COMMENT | SHARE | SUBSCRIBE
=====================================
==========
Website https://www.tecengineering.in/
Facebook / tecengineeri. .
WhatsApp Group :- https://chat.whatsapp.com/FF44hTGJ2kS...
whatsApp Group :- https://chat.whatsapp.com/KMr7yHHiW5k...
Telegram Group :- https://t.me/joinchat/R2n5DxifyxVSWaz...
================================================
==============
WhatsApp Number +917036691232
E-Mai :- [email protected]
Any hvac & mep design & Drafting please contact me
Panasonic AC Error Code | Panasonic Error Code List
• Panasonic AC Error Code | Panasonic E...
LG AC Error Code | LG inverter split AC error CH 12, CH 10, CH 05
• LG AC Error Code | LG inverter split ...
Haier Ac Error Code | Haier Ac f1 Error Solution
• Haier Ac Error Code | Haier Ac f1 Err...
Hitachi Error Code List | Hitachi Error Code p09
• Hitachi Error Code List | Hitachi Err...
#carrier
#error code
#ac error code
E1 - Indoor / outdoor communication.
E3 - Indoor fan Motor.
E4 - Indoor room temp. sensor.
E5 - Evaporator coil temp. sensor.
EC - Refrigerant Leakage.
F1 - Outdoor temp sensor open.
F2 - Condenser coil temp. sensor open.
F3 - Compressor discharge temp.sensor.
F4 - Outdoor unit EEPROM parameter.
F5 - Outdoor fan speed has been out of control
P0 - IPM malfunction or IGBT.
P1 - Over voltage or over low voltage.
E0 - Outdoor EEPROM malfunction.
E2 - Indoor/outdoor units communication.
E3 - IPM board and outdoor main board.
E4 - Open or short circuit of outdoor.
E8 - Outdoor fan speed.
F1 - Indoor unit coil connector of sensor is defective
- Defrost Mode.
0A - Defrost Mode 2.
F0 - Low charge or refrigeration system blockage.
F3 - Outdoor ambient temperature sensor malfunction.
F4 - Outdoor mid-coil temperature sensor malfunction.
F5 - Outdoor discharge air temperature sensor.
F7 - Cooling oil return cycle.
E1 - System high pressure.
E2 - Indoor freeze.
E3 - System low pressure.
E4 - Compressor discharge high temperature.
E6 - Communication error between indoor and outdoor.
E7 - Mode conflict.
E8 - System overload.
E9 - Cold Blow.
Dd - Test mode.
Fo - Pump down mode.
P0 - IPM Rest.
P5 - Compressor current.
P6 – Communication error between the inverter drive and main board.
P7 - Heat sink temperature sensor malfunction.
P8 - IPM over temperature protection.
P9 - Open Contactor.
Pc - Current sensor malfunction.
Pd - Current sensor miss-wiring Protection.
PA - Input current.
PF - Inverter board ambient temperature sensor malfunction.
PL - Low voltage.
PH - High voltage.
PP - Abnormal input AC voltage.
PU - Capacitor charging malfunction.
H1 - Heating oil return cycle.
H2 - Forced defrost.
H3 - Compressor overheat.
H5 - IPM Protection.
H7 - Compressor speed reduction.
Hc - PFC board.
L9 - Compressor high voltage.
Lc - Compressor start-up failure.
Ld - Compressor phase loss.
LE - Compressor stalling.
LF - Compressor over-speed.
A5 - Condenser coil inlet temp sensor malfunction.
A7 - Condenser outlet temperature sensor malfunction.
EE - Memory card error.
En - Frequency limitation for module circuit protection.
EU - Frequency limitation for module temperature protection.
F6 - Frequency limitation for overload protection.
F8 - Frequency limitation for system circuit protection.
F9 - Frequency limitation for module circuit protection.
FH - Frequency limitation for freeze protection.
HE - Compressor demagnetizing protection.
LP - Indoor and outdoor units mismatch.
U1 - Compressor phase detection malfunction.
U3 - Low DC bus voltage.
Dn - Communication error between main board and EXV.
13 - Unit A indoor pipe outlet temperature sensor malfunction.
14 - Unit A indoor pipe inlet Temperature sensor malfunction.
15 – Unit A Indoor return air sensor malfunction.
16 - Unit A mode conflict.
17 - Unit A freeze protection.
23 - Unit B indoor pipe outlet temperature sensor malfunction.
24 - Unit B indoor pipe inlet temperature sensor malfunction
25 - Unit B Indoor return air sensor malfunction.
26 - Unit B mode conflict.
27 - Unit B freeze protection.
33 - Unit C indoor unit pipe outlet temperature sensor malfunction.
34 - Unit C indoor unit pipe inlet temperature sensor malfunction.
35 - Unit C Indoor unit return air sensor malfunction.
36 - Unit C mode conflict.
37 - Unit C freeze protection.
41
42 - Indoor return air temperature sensor malfunction.
43 - Unit D indoor pipe outlet temperature sensor malfunction.
44
45
46
47
51,52,53,54,55,56,57,C5